Scania R230 remap

Diesel · Flash via OBD · Figures published for this engine · Remote remap available UK-wide from £199

The Scania R230 makes 310 bhp and 1550 Nm as standard. A Stage 1 ECU remap takes it to 360 bhp and 1740 Nm, a gain of 50 bhp (16%) with no hardware changes. Remap risk for this engine is low, 3 out of 10.

Standard

310 bhp

1550 Nm

Stage 1

360 bhp

1740 Nm · +50 bhp

Remap risk

LOW

3 / 10

Is a remap worth it on the Scania R230?

A modest but real gain. Worth it for drivability and mid-range pull rather than headline power.

What each stage needs

Stage	Power	Torque	Hardware
Standard	310 bhp	1550 Nm	None
Stage 1	360 bhp	1740 Nm	Software only

Risk on this engine: low

Significant 16% gain: boost and fuelling pushed beyond factory settings.
Diesel: no knock risk. Primary risks are EGT, turbo health, and injector wear.

How to keep the risk down

Check intercooler efficiency before tuning.
Monitor EGT under hard driving: sustained temps above 700 C accelerate turbo wear.
Keep a copy of the original ECU file before flashing.

Remote remap for your Scania R230: Stage 1 from £199

No trip to a workshop. ORCA Remapping, part of the same company as BeakCheck, tunes your car's own ECU file and sends it back, UK-wide.

Read the ECUWith your own tool (AutoTuner, KESS3, Alientech KTM, MPPS V21) or a local garage that has one. Takes a few minutes through the OBD port.

ORCA tunes the fileA calibration for this exact engine, checked against 55 safety limits, back in one to three days.

Flash it backYour stock file is kept as a backup, so it is fully reversible, with 30 days of support.

Service	Price	Needs
Stage 1 Remote	£199	Standard car, software only. 360 bhp and 1740 Nm on this engine.
Diagnostic file analysis	£49	Read-only check of the existing file: detects a previous tune before you buy a used car.

Paid up front on orcahq.co.uk once ORCA confirms your engine and tool. Or ask first, no obligation:

Questions owners ask

How much power does a Scania R230 gain from a remap?

A Stage 1 remap adds about 50 bhp and 190 Nm, taking it from 310 to 360 bhp. Stage 1 is software only.

Is it safe to remap a Scania R230?

Remap risk is rated low (3/10). Significant 16% gain: boost and fuelling pushed beyond factory settings. Check intercooler efficiency before tuning.

Does a remap affect the MOT or insurance on a Scania R230?

A remap does not affect the MOT test, which does not read the ECU calibration. It is a modification for insurance purposes and must be declared to your insurer; most mainstream insurers accept a declared Stage 1 with a premium adjustment.

How is a Scania R230 remapped?

Through the OBD diagnostic port in the cabin. The original file is read and saved first, then the modified calibration is written. Typically under two hours.

Check your exact car by registration

Free DVLA and MOT check, plus the remap verdict for the engine actually fitted to your car.

Other Scania engines

Scania P230 · +50 bhp Scania P230 · +50 bhp Scania P270 · +50 bhp Scania P310 · +50 bhp Scania P340 · +60 bhp Scania R230 · +50 bhp Scania R270 · +50 bhp Scania R310 · +50 bhp

All Scania remaps

Remapping guides

What Is an ECU Remap? A Plain-English Guide for UK Drivers Is Remapping a Car Worth It? An Honest UK Guide Stage 1 vs Stage 2 Remap: What Is the Difference?

Power figures are published Stage 1 and Stage 2 results for this engine and are a guide. Actual gains depend on the car's condition, fuel and the map used. BeakCheck and ORCA Remapping are trading names of Bloor Engineering Ltd.